jackwakaka

回覆 10# KinChungE

我LEE 幾日OBSERVE 左個BIOS, 我開左XMP 就可能一兩次開機會出現無畫面要REBOOT 然後出現OVERCLOCKING FAILED, 所以我都唔知幾時會突然FAIL, 會唔會係CORSAIR RAM 問題? 我話說已經UPDATE 左BIOS....你講既IMC 加壓係咪就係VCCIO?

KinChungE

回覆  KinChungE

我LEE 幾日OBSERVE 左個BIOS, 我開左XMP 就可能一兩次開機會出現無畫面要REBOOT 然後出 ...
jackwakaka 發表於 2016-12-27 01:10

BCLK 102.25 <-- 唔怪得唔穩定啦, BCLK唔好郁佢
DRAM Voltage <-- 1.35v咁低當然上唔到3000

jackwakaka

回覆 12# KinChungE

但我係XMP 佢自己GEN 出黎~我降低佢個FREQUENCY  就跌左去24XX

同埋個VOLTAGE 1.35 都係XMP GEN 出黎 CORSAIR 個網係咁SHOW....
Technical Specifications

Density: 16GB (2 x 8GB)
Speed: 3000MHz
Tested Latency: 15-17-17-35
Voltage: 1.35V

我唔識呀 嗚T0T

KinChungE

回覆  KinChungE

但我係XMP 佢自己GEN 出黎~我降低佢個FREQUENCY  就跌左去24XX

同埋個VOLTAGE 1.35 都 ...
jackwakaka 發表於 2016-12-27 01:39

http://forum3.hkgolden.com/view. ... type=HW&page=30
情況類似, 一開XMP就變左102.25, 死硬
要set翻100, 手動set其他資料

你用XMP黎行3000,佢會同你set左102.25外頻,咁樣超左你粒non-K咪有機會boot唔到
你可以手動set返做100外頻,但行唔到3000只能取相近數值2933或3066

jackwakaka

如果我要3000 就要加電超條ram 係咪? 我set 番做一百條u 就唔會超? 我宜家照跟default 開xmp, bclk 去番100, 行緊2933.....

sorry i am stupid T0T

jackwakaka

PT100

回覆 12# KinChungE

DRAM Voltage <-- 1.35v咁低當然上唔到3000 < < <

I also use this ram, 3000Mhz could only running stable on 1.35V at cl16

My parameter 16-17-17-35-391clocks - 2T, just for reference !

It might be a reference for him

KinChungE

回覆  KinChungE

DRAM Voltage
PT100 發表於 2016-12-27 19:57

仲以為條RAM咁好, 1.35V 3000 CL15
原來流既

jackwakaka

I know nothing about it T0T

jackwakaka

回覆 17# PT100

Thanks a lot, i will try it T0T

回覆 18# KinChungE

宜家SET 左MANUAL, BCLK 100, CL 15 17 35- 2T, 2933MHZ , 1.350V , 係咪要MENTEST 先知???