1 ...13141516171819202122... 42
返回列表 發帖
dtom

Rank: 3Rank: 3Rank: 3
141# 跳轉到 »
發表於 2013-3-3 23:39 | 只看該作者
有無SET好個中位先?
brianyzf 發表於 2013-3-3 22:37



即係開機前噴咀要係板上面, X/Y 係中間?

TOP

brianyzf

Rank: 3Rank: 3Rank: 3
142#
發表於 2013-3-4 00:00 | 只看該作者
即係開機前噴咀要係板上面, X/Y 係中間?
dtom 發表於 2013-3-3 23:39


我部機買返黎時以經話SET好左，但係正常你部機要自己砌，所以應該無SET好中位，所以部機唔會識得邊度係中位，你要先SET好一次，咁部機先會記住。
http://www.come3d.com/faq/correction/

TOP

dtom

Rank: 3Rank: 3Rank: 3
143#
發表於 2013-3-4 00:45 | 只看該作者
本帖最後由 dtom 於 2013-3-4 00:48 編輯
我部機買返黎時以經話SET好左，但係正常你部機要自己砌，所以應該無SET好中位，所以部機唔會識得邊度係中 ...
brianyzf 發表於 2013-3-4 00:00



thx, 係 control panel 正常 (3 軸 Home/Center)
Extruder 同 Hotbad 都試過升到溫, 不過風扇子就未轉過... 咩情況下先轉呢, 我怕駁錯線

但一 print 就彈一堆 error

ScreenShot115.jpg

Procced anyway 就走到左前(XY無 endstop 個邊), 又係走到唔識停, 仲差D乜呢?

TOP

ma_hty

Rank: 3Rank: 3Rank: 3
144#
發表於 2013-3-4 07:25 | 只看該作者
thx, 係 control panel 正常 (3 軸 Home/Center)
Extruder 同 Hotbad 都試過升到溫, 不過風扇子就未轉過 ...
dtom 發表於 2013-3-4 00:45


比個 gcode 來睇睇.

順帶一提, 你的 machine profile 選錯, 應該係 Thingomatic w/ HBP and Steptruder MK7.
HBP - Headed Build Platform - 加熱平台
ABP - Automatic Build Platform - 自動運送平台 - http://www.youtube.com/watch?v=lsPkDty9zCA

TOP

brianyzf

Rank: 3Rank: 3Rank: 3
145#
發表於 2013-3-4 07:58 | 只看該作者
我把風扇一著機就轉，你把風扇接左去邊個位?
一堆error好大機會真係揀錯野，你可以試試先跟我比你條link既come3d咁set，replicatorG你係唔係用0040?如果係有幾個地方要set岩先得，我第一次轉用0040都有error，因為原setting係比replicator2用，你先試set，再唔得今晚我返屋企先cap 我個setting比你睇下係唔係有唔同。

TOP

dtom

Rank: 3Rank: 3Rank: 3
146#
發表於 2013-3-4 08:26 | 只看該作者
本帖最後由 dtom 於 2013-3-4 08:30 編輯
比個 gcode 來睇睇.

順帶一提, 你的 machine profile 選錯, 應該係 Thingomatic w/ HBP and Steptruder  ...
ma_hty 發表於 2013-3-4 07:25


THX, 改返 machine type 喇但結果一樣
Slicing 本來想用 Skeinforge, 但係 Gen GCode 彈野
ScreenShot118.jpg


唯有用 Slic3r
ScreenShot117.jpg


Profiles 只有 Replicator, 問題係度?
ScreenShot116.jpg


GCode:
  1. ; ; generated by Slic3r 0.7.1 on 2013-03-04 at 08:10:24

  3. ; layer_height = 0.02
  4. ; perimeters = 3
  5. ; solid_layers = 3
  6. ; fill_density = 0.4
  7. ; nozzle_diameter = 0.4
  8. ; filament_diameter = 2.94
  9. ; extrusion_multiplier = 1
  10. ; perimeter_speed = 30
  11. ; infill_speed = 60
  12. ; travel_speed = 130
  13. ; extrusion_width_ratio = 0
  14. ; scale = 1
  15. ; single wall width = 0.56mm

  17. M104 S200 ; set temperature
  18. (**** start.gcode for The Replicator, single head ****)
  19. M103 (RPM off)
  20. M73 P0 (enable build progress)
  21. G21 (set units to mm)
  22. G90 (set positioning to absolute)
  23. (**** begin homing ****)
  24. G162 X Y F2500 (home XY axes maximum
  25. G161 Z F1100 (home Z axis minimum)
  26. G92 Z-5 (set Z to -5)
  27. G1 Z0.0 (move Z to "0")
  28. G161 Z F100 (home Z axis minimum)
  29. M132 X Y Z A B (Recall stored home offsets for XYZAB axis)
  30. (**** end homing ****)
  31. G1 X-110.5 Y-74 Z150 F3300.0 (move to waiting position)
  32. G130 X0 Y0 A0 B0 (Lower stepper Vrefs while heating)
  33. M6 T0 (wait for toolhead, and HBP to reach temperature)
  34. G130 X127 Y127 A127 B127 (Set Stepper motor Vref to defaults)
  35. M108 R3.0 T0
  36. G0 X-110.5 Y-74 (Position Nozzle)
  37. G0 Z0.6      (Position Height)
  38. M108 R4.0    (Set Extruder Speed)
  39. M101         (Start Extruder)
  40. G4 P1500     (Create Anchor)
  41. (**** end of start.gcode ****)
  42. G90 ; use absolute coordinates
  43. G21 ; set units to millimeters
  44. M106 S254
  45. G1 Z0.020 F7800.000
  46. G1 X-8.312 Y-8.132
  47. G1 F1800.000 E1.00000
  48. G1 X-8.132 Y-8.312 F540.000 E1.00042
  49. G1 X-7.752 Y-8.652 E1.00125
  50. G1 X-7.132 Y-9.092 E1.00250
  51. G1 X-6.912 Y-9.222 E1.00291
  52. G1 X-6.452 Y-9.452 E1.00376
  53. G1 X-5.982 Y-9.642 E1.00459
  54. G1 X-5.492 Y-9.792 E1.00543
  55. G1 X-5.242 Y-9.852 E1.00585
  56. G1 X-4.492 Y-9.962 E1.00709
  57. G1 X-3.982 Y-9.982 E1.00792
  58. G1 X4.488 Y-9.962 E1.02179
  59. G1 X5.238 Y-9.852 E1.02303
  60. G1 X5.738 Y-9.722 E1.02388
  61. G1 X6.218 Y-9.552 E1.02471
  62. G1 X6.678 Y-9.342 E1.02554
  63. G1 X6.908 Y-9.222 E1.02596
  64. G1 X7.128 Y-9.092 E1.02638
  65. G1 X7.748 Y-8.652 E1.02763
  66. G1 X8.128 Y-8.312 E1.02846
  67. G1 X8.308 Y-8.132 E1.02888
  68. G1 X8.648 Y-7.752 E1.02971
  69. G1 X9.088 Y-7.132 E1.03096
  70. G1 X9.218 Y-6.912 E1.03138
  71. G1 X9.448 Y-6.452 E1.03222
  72. G1 X9.638 Y-5.982 E1.03305
  73. G1 X9.788 Y-5.492 E1.03389
  74. G1 X9.848 Y-5.242 E1.03431
  75. G1 X9.958 Y-4.492 E1.03555
  76. G1 X9.958 Y4.488 E1.05025
  77. G1 X9.848 Y5.238 E1.05149
  78. G1 X9.718 Y5.738 E1.05234
  79. G1 X9.548 Y6.218 E1.05317
  80. G1 X9.338 Y6.678 E1.05400
  81. G1 X9.218 Y6.908 E1.05442
  82. G1 X9.088 Y7.128 E1.05484
  83. G1 X8.648 Y7.748 E1.05609
  84. G1 X8.308 Y8.128 E1.05692
  85. G1 X8.128 Y8.308 E1.05734
  86. G1 X7.748 Y8.648 E1.05817
  87. G1 X7.128 Y9.088 E1.05942
  88. G1 X6.908 Y9.218 E1.05984
  89. G1 X6.448 Y9.448 E1.06068
  90. G1 X5.978 Y9.638 E1.06151
  91. G1 X5.488 Y9.788 E1.06235
  92. G1 X5.238 Y9.848 E1.06277
  93. G1 X4.488 Y9.958 E1.06401
  94. G1 X3.978 Y9.978 E1.06484
  95. G1 X-4.492 Y9.958 E1.07871
  96. G1 X-5.242 Y9.848 E1.07995
  97. G1 X-5.742 Y9.718 E1.08080
  98. G1 X-6.222 Y9.548 E1.08163
  99. G1 X-6.682 Y9.338 E1.08246
  100. G1 X-6.912 Y9.218 E1.08288
  101. G1 X-7.132 Y9.088 E1.08330
  102. G1 X-7.752 Y8.648 E1.08455
  103. G1 X-8.132 Y8.308 E1.08538
  104. G1 X-8.312 Y8.128 E1.08580
  105. G1 X-8.652 Y7.748 E1.08663
  106. G1 X-9.092 Y7.128 E1.08788
  107. G1 X-9.222 Y6.908 E1.08830
  108. G1 X-9.452 Y6.448 E1.08914
  109. G1 X-9.642 Y5.978 E1.08997
  110. G1 X-9.792 Y5.488 E1.09081
  111. G1 X-9.852 Y5.238 E1.09123
  112. G1 X-9.962 Y4.488 E1.09247
  113. G1 X-9.962 Y-4.492 E1.10717
  114. G1 X-9.852 Y-5.242 E1.10841
  115. G1 X-9.722 Y-5.742 E1.10926
  116. G1 X-9.552 Y-6.222 E1.11009
  117. G1 X-9.342 Y-6.682 E1.11092
  118. G1 X-9.222 Y-6.912 E1.11134
  119. G1 X-9.092 Y-7.132 E1.11176
  120. G1 X-8.652 Y-7.752 E1.11301
  121. G1 X-8.368 Y-8.070 E1.11370
  122. G1 F1800.000 E0.11370
  123. G92 E0
  124. G1 X-2.867 Y-2.867 F7800.000
  125. G1 F1800.000 E1.00000
  126. G1 X2.867 Y-2.867 F540.000 E1.00939
  127. G1 X2.867 Y2.867 E1.01877
  128. G1 X-2.867 Y2.867 E1.02816
  129. G1 X-2.867 Y-2.783 E1.03741
  130. G1 X-3.424 Y-3.424 F7800.000
  131. G1 X3.424 Y-3.424 F540.000 E1.04862
  132. G1 X3.424 Y3.424 E1.05983
  133. G1 X-3.424 Y3.424 E1.07105
  134. G1 X-3.424 Y-3.340 E1.08212
  135. G1 X-3.982 Y-3.982 F7800.000
  136. G1 X3.982 Y-3.982 F540.000 E1.09516
  137. G1 X3.982 Y3.982 E1.10820
  138. G1 X-3.982 Y3.982 E1.12124
  139. G1 X-3.982 Y-3.898 E1.13414
  140. G1 F1800.000 E0.13414
  141. G92 E0
  142. G1 X1.714 Y-2.467 F7800.000
  143. G1 F1800.000 E1.00000
  144. G1 X2.467 Y-1.714 F1080.000 E1.00195
  145. G1 X2.467 Y-0.878 E1.00349
  146. G1 X0.878 Y-2.467 E1.00761
  147. G1 X0.042 Y-2.467 E1.00914
  148. G1 X2.467 Y-0.042 E1.01544
  149. G1 X2.467 Y0.795 E1.01697
  150. G1 X-0.795 Y-2.467 E1.02543
  151. G1 X-1.631 Y-2.467 E1.02697
  152. G1 X2.467 Y1.631 E1.03760
  153. G1 X2.467 Y2.467 E1.03913
  154. G1 X-2.467 Y-2.467 E1.05193
  155. G1 X-2.467 Y-1.631 E1.05347
  156. G1 X1.631 Y2.467 E1.06410
  157. G1 X0.795 Y2.467 E1.06563
  158. G1 X-2.467 Y-0.795 E1.07409
  159. G1 X-2.467 Y0.042 E1.07563
  160. G1 X-0.042 Y2.467 E1.08192
  161. G1 X-0.878 Y2.467 E1.08345
  162. G1 X-2.467 Y0.878 E1.08758
  163. G1 X-2.467 Y1.714 E1.08911
  164. G1 X-1.714 Y2.467 E1.09106
  165. M106 S254
  166. G1 F1800.000 E0.09106
  167. G92 E0
  168. G1 Z0.040 F7800.000
  169. .
  170. .
  171. 中間既野差唔多, 唔夠位刪減下
  172. .
  173. .
  174. G92 E0
  175. G1 X1.714 Y-2.467 F7800.000
  176. G1 F1800.000 E1.00000
  177. G1 X2.467 Y-1.714 F3600.000 E1.00195
  178. G1 X2.467 Y-0.878 E1.00349
  179. G1 X0.878 Y-2.467 E1.00761
  180. G1 X0.042 Y-2.467 E1.00914
  181. G1 X2.467 Y-0.042 E1.01544
  182. G1 X2.467 Y0.795 E1.01697
  183. G1 X-0.795 Y-2.467 E1.02543
  184. G1 X-1.631 Y-2.467 E1.02697
  185. G1 X2.467 Y1.631 E1.03760
  186. G1 X2.467 Y2.467 E1.03913
  187. G1 X-2.467 Y-2.467 E1.05193
  188. G1 X-2.467 Y-1.631 E1.05347
  189. G1 X1.631 Y2.467 E1.06410
  190. G1 X0.795 Y2.467 E1.06563
  191. G1 X-2.467 Y-0.795 E1.07409
  192. G1 X-2.467 Y0.042 E1.07563
  193. G1 X-0.042 Y2.467 E1.08192
  194. G1 X-0.878 Y2.467 E1.08345
  195. G1 X-2.467 Y0.878 E1.08758
  196. G1 X-2.467 Y1.714 E1.08911
  197. G1 X-1.714 Y2.467 E1.09106
  198. G1 F1800.000 E0.09106
  199. G92 E0
  200. M107
  201. (******* End.gcode*******)
  202. M73 P100 ( End  build progress )
  203. G0 Z150 ( Send Z axis to bottom of machine )
  204. M18 ( Disable steppers )
  205. M109 S0 T0 ( Cool down the build platform )
  206. M104 S0 T0 ( Cool down the Right Extruder )
  207. M104 S0 T0 ( Cool down the Left Extruder )
  208. G162 X Y F2500 ( Home XY endstops )
  209. M18 ( Disable stepper motors )
  210. M70 P5 ( We <3 Making Things!)
  211. M72 P1  ( Play Ta-Da song )
  212. (*********end End.gcode*******)
  213. ; filament used = 49.1mm (0.3cm3)
  214. *****)
  215. ; filament used = 49.1mm (0.3cm3)
複製代碼

TOP

dtom

Rank: 3Rank: 3Rank: 3
147#
發表於 2013-3-4 08:35 | 只看該作者
本帖最後由 dtom 於 2013-3-4 08:37 編輯
我把風扇一著機就轉，你把風扇接左去邊個位?
一堆error好大機會真係揀錯野，你可以試試先跟我比你條link既c ...
brianyzf 發表於 2013-3-4 07:58


風扇插 1,2
20130303_143015.jpg

官網說明
ScreenShot004.jpg

TOP

brianyzf

Rank: 3Rank: 3Rank: 3
148#
發表於 2013-3-4 08:38 | 只看該作者
該用35果個，你係唔係用左50?

TOP

brianyzf

Rank: 3Rank: 3Rank: 3
149#
發表於 2013-3-4 08:54 | 只看該作者
不如你試下dl come3d網果個29r2 version，果個version 基本上你乜都可以唔駛set，跟住佢個教學巳經用到，set好晒野先用0040。

TOP

ma_hty

Rank: 3Rank: 3Rank: 3
150#
發表於 2013-3-4 08:59 | 只看該作者
本帖最後由 ma_hty 於 2013-3-4 09:03 編輯
THX, 改返 machine type 喇但結果一樣
Slicing 本來想用 Skeinforge, 但係 Gen GCode 彈野

dtom 發表於 2013-3-4 08:26


你要先安裝 Python, 才能用 Skeinforge.  安裝 Python 吧, 安全的,  它是寫程式的人常用的 Scripting Engine.

TOP

1 ...13141516171819202122... 42
返回列表