標題: [開箱文] Swiftech Apogee XT [打印本頁]

---

作者: kumakuba    時間: 2009-12-6 20:32     標題: [開箱文] Swiftech Apogee XT

外觀比 apogee gtx 更靚仔




跟 775, 1156, 1366 backplate


解體





個人覺得設計同 hk 3.0 類似



據官方"聲稱"效能比 HEATKILLER 低 1 度

Intel® Core™ i7 920 (Bloomfield D0) (@4095 Mhz - 1.392 V Actual)
Water-Block	Delta T (*)
Apogee™ GTZ	40.82 °C
Apogee™ XT (factory inlet configuration)	37.88 °C
Apogee™ XT (alternate inlet configuration) (**)	37.99 °C
Reference competitive data (Heatkiller rev3.0)	39.39 °C

Comments:

• In factory configuration, the Apogee™ XT showed a 3°C improvement over the Apogee™ GTZ.
• A 1.5 °C improvement was observed compared the best competitive waterblock tested in our lab.
• The temperature degradation between factory inlet configuration and alternate inlet configuration was 0.1°C

(*) Delta T is the difference in temperature between averaged CPU core temperature as reported by RealTemp and averaged air temperature reported by 3 thermal probes located at the fans inlets.
(**) Alternate inlet configuration is when the inlet is rotated at 180° to allow installation of extra large compression fittings.

測試留待加埋下面呢樣o野繼續



[ 本帖最後由 kumakuba 於 2009-12-6 20:43 編輯 ]

圖片附件: CIMG1563.jpg (2009-12-6 20:32, 242.57 KB) / 下載次數 26
https://h1.hkepc.com/forum/attachment.php?aid=976969&k=d05abeaa04035c82fd1992347f2e6f09&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1564.jpg (2009-12-6 20:32, 223.48 KB) / 下載次數 27
https://h1.hkepc.com/forum/attachment.php?aid=976970&k=867e09e8ed17d92fe7f075bf571c1568&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1565.jpg (2009-12-6 20:32, 226.22 KB) / 下載次數 25
https://h1.hkepc.com/forum/attachment.php?aid=976971&k=87423affb0caea7ea4fea6311e6a4640&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1582.jpg (2009-12-6 20:32, 218.51 KB) / 下載次數 29
https://h1.hkepc.com/forum/attachment.php?aid=976972&k=6ed38f2a9f727324697b77ab5f94cc02&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1585.jpg (2009-12-6 20:32, 230.25 KB) / 下載次數 28
https://h1.hkepc.com/forum/attachment.php?aid=976973&k=2d250f0125aed95e0ff6b1c4c17c0327&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1588.jpg (2009-12-6 20:32, 211.33 KB) / 下載次數 25
https://h1.hkepc.com/forum/attachment.php?aid=976974&k=f70a01aea17d2df6d88e883c3cce1557&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1590.jpg (2009-12-6 20:32, 229.91 KB) / 下載次數 23
https://h1.hkepc.com/forum/attachment.php?aid=976975&k=f773fc5c201765e7115027b7665860c7&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1591.jpg (2009-12-6 20:32, 235.47 KB) / 下載次數 20
https://h1.hkepc.com/forum/attachment.php?aid=976976&k=b200d9cdbf86fec286688823206ccca5&t=1782418927&sid=4sHHYQPhAl



圖片附件: CIMG1364.jpg (2009-12-6 20:32, 237.56 KB) / 下載次數 28
https://h1.hkepc.com/forum/attachment.php?aid=976977&k=92515a87a89a6ba71f5a9643671f1bf7&t=1782418927&sid=4sHHYQPhAl



圖片附件: 未命名.jpg (2009-12-6 20:43, 114.46 KB) / 下載次數 25
https://h1.hkepc.com/forum/attachment.php?aid=976983&k=791fee58d0728d7bc73d4009108feef5&t=1782418927&sid=4sHHYQPhAl

---

作者: felixku    時間: 2009-12-6 20:35

真係靚仔,不過覺得gtz好睇啲..

---

作者: highflyer    時間: 2009-12-6 21:05

張pins 相睇得唔清楚.  點解好似好多''銹漬''?
同埋我見有外國玩家話新入手都有d pins 彎左,  你自己快d逐條pin 睇下啦.

我同你都係用Boreas TEC, 都係同門師兄弟, 我還先你入門學武, 點解師父偏心, 俾apogee xt 你, 我得hk 3.0  o查.

(EK Supreme HF 就快出, 唔知會唔會有大效能增長呢? )

---

作者: kumakuba    時間: 2009-12-6 21:16



可以點清走佢 ?

[ 本帖最後由 kumakuba 於 2009-12-6 21:55 編輯 ]

---

作者: jeff_extergo    時間: 2009-12-6 21:30

係我睇錯或是做工問題

圖片附件: 20091206_a6b43d2d2e7c2274dcf3n4LPU7RsjCgP.jpg (2009-12-6 21:30, 120.73 KB) / 下載次數 22
https://h1.hkepc.com/forum/attachment.php?aid=976992&k=ed7c434b94ab86bf7a0eefb36d84aeb8&t=1782418927&sid=4sHHYQPhAl

---

作者: kumakuba    時間: 2009-12-6 21:43



我之前隻 HK 3.0 都唔係百分百完美

---

作者: k2t4    時間: 2009-12-6 21:47



微水道 刀路 太 精細 啦
做工 要求 唔可以 咁完美

[ 本帖最後由 k2t4 於 2009-12-6 21:56 編輯 ]

---

作者: 3R1C    時間: 2009-12-6 21:56

有冇都係行微水道既luna既test對比下呢?

---

作者: k2t4    時間: 2009-12-6 22:22



Enzotech Luna  點可以同 Swiftech Apogee XT 相比 啦  


http://vapor.skinneelabs.com/i7/Round2/Overall/R2i7Overall.html

[ 本帖最後由 k2t4 於 2009-12-6 22:33 編輯 ]

---

作者: Lelouchvi    時間: 2009-12-6 23:34

ENZOTECH咁低既 ~~ 大家都係用MICROPIN

---

作者: jeff_extergo    時間: 2009-12-6 23:44



咁個價錢都有番咁上下啦
Enzotech 中高階黎講算係平民價的了

---

作者: highflyer    時間: 2009-12-7 00:01



試下用番茄醬或者食用醋

---

作者: highflyer    時間: 2009-12-7 00:02



據聞made in china 間工廠個QC 出左d 問題.
呢度有2 位外國chings 隻XT, 都幾恐怖.

圖片附件: apogee xt made in china.jpg (2009-12-7 00:02, 141.01 KB) / 下載次數 13
https://h1.hkepc.com/forum/attachment.php?aid=977052&k=7b5a6feabbf7ffe7141d84bce7c65651&t=1782418927&sid=4sHHYQPhAl



圖片附件: apogee xt QC problem sample 1.jpg (2009-12-7 00:02, 117.26 KB) / 下載次數 17
https://h1.hkepc.com/forum/attachment.php?aid=977053&k=a180e27446f3964b9fe7ad7f5b67cce0&t=1782418927&sid=4sHHYQPhAl



圖片附件: apogee xt QC problem sample 2.JPG (2009-12-7 00:02, 115.67 KB) / 下載次數 18
https://h1.hkepc.com/forum/attachment.php?aid=977054&k=cf7d6f114b5b574b18617248659d241e&t=1782418927&sid=4sHHYQPhAl

---

作者: jeff_extergo    時間: 2009-12-7 00:14




真係直頭亂開wo

---

作者: kumakuba    時間: 2009-12-7 00:16     標題: 回覆 13# 的帖子

我隻算好靚喇喎

---

作者: dannyctl    時間: 2009-12-7 00:20



搞到買嘢好似抽獎咁...   萬一中咗... 都唔知有冇得退!!

---

作者: Lelouchvi    時間: 2009-12-7 00:21     標題: 回覆 16# 的帖子

嘩我仲諗住買TIM ~~ 都係睇定D先

---

作者: Lelouchvi    時間: 2009-12-7 00:22

HK幾多錢呀?

---

作者: bb8388    時間: 2009-12-7 09:20


How much

---

作者: lmy0148    時間: 2009-12-7 10:38     標題: 回覆 19# 的帖子

代答, 無記錯應該係hk$8xx, 因為小弟都訂左隻..

---

作者: wonderful    時間: 2009-12-7 15:15


better keep my HK 3.0..............................