標題: 求助：e1200 flash完tomato後就只入唔返。 [打印本頁]

---

作者: 病態賭徒    時間: 2014-11-17 18:41     標題: 求助：e1200 flash完tomato後就只入唔返。

用Mac check IP 就show 168.254.x.x

係咪已經brick了？

---

作者: tomleehk    時間: 2014-11-17 19:10

本帖最後由 tomleehk 於 2014-11-17 19:11 編輯

1) After power on, did the power LED keep on flashing without stop ?
2) What was the firmware filename you used to flash to your E1200 ?

---

作者: 病態賭徒    時間: 2014-11-17 19:13

1) yes
2) need to check, left in office

---

作者: tomleehk    時間: 2014-11-17 21:45

本帖最後由 tomleehk 於 2014-11-17 22:01 編輯

1) Power off router and connect LAN cable to any LAN port of router.

2) Configure the local network adapter on the laptop to a Static IP of 192.168.1.25, Netmask 255.255.255.0, and Default Gateway of 192.168.1.1.

3) From a command prompt, type ping -t 192.168.1.1  , hit <ENTER>  (which will show the laptop attempting to repeatedly ping the bricked router)

4) Then plug the router to power on and see if there is any response at the command windows within first 15 seconds...

---

作者: tomleehk    時間: 2014-11-17 22:07

本帖最後由 tomleehk 於 2014-11-18 09:25 編輯

http://www.dd-wrt.com/phpBB2/vie ... e23b9e32e52ea153817
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=318082#318082
http://www.dd-wrt.com/phpBB2/vie ... d845440f39d79dc1c05
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=155978
https://www.ifixit.com/Guide/Dis ... Linksys+E1200/22917

---

作者: 病態賭徒    時間: 2014-11-18 10:44

typo

169.254.x.x

2) tomato-K26-1.28.9054MIPSR2-beta-Std


thanks for your research, I will study after finishing office work

btw, if fail, can I send back to repair?

---

作者: tomleehk    時間: 2014-11-18 12:34

本帖最後由 tomleehk 於 2014-11-18 12:40 編輯

Q1>  btw, if fail, can I send back to repair?
A1>  I am afraid you have to ask the 代理 and see if the cost is really worth..

This looks like dd-wrt (as well as its forum) was down by noon today..

---

作者: 病態賭徒    時間: 2014-11-18 12:40




    bcoz it is under warranty

---

作者: tomleehk    時間: 2014-11-18 12:43

本帖最後由 tomleehk 於 2014-11-18 12:45 編輯


Under warranty ..

Don't open the case ...

Send to 代理 and see if they use their own way to fix it or replace a new one for you..

However,  don't mention what you have done as what you have done manually is definitely beyond warranty coverage..

---

作者: 病態賭徒    時間: 2014-11-18 12:46

let see see if I can fix.....

thanks million tomleehk

---

作者: tomleehk    時間: 2014-11-18 12:59

本帖最後由 tomleehk 於 2014-11-18 13:07 編輯

Based on my knowledge, for Linksys E-series, it is better and safer to flash with customized firmware dedicated for that particular model/version. Customized/Dedicated firmware can easily identified by the filename.

e.g.  
tomato-E1200v2-NVRAM64K-1.28.05066.3MIPSR2Toastman-RT-N-VLAN-Std.bin
at http://www.4shared.com/dir/v1BuI ... s.html#dir=sz5zA-5p

tomato-E1200v2-NVRAM64K-1.28.RT-N5x-MIPSR2-123-Max.bin
at http://tomato.groov.pl/download/ ... Linksys%20E-series/

Flashing with non-dedicated firmware may brick the Linksys E-series router..

---

作者: 病態賭徒    時間: 2014-11-19 12:31

just check, 代理 is in 小瀝源 and not open on Sat

very PK, ahahahah

---

作者: tomleehk    時間: 2014-11-19 13:34

Newly purchased ?

If so, go to the retail shop where you purchased and have it replaced within 7 days ...

---

作者: 病態賭徒    時間: 2014-11-19 14:21

more than la

---

作者: 病態賭徒    時間: 2014-11-21 16:29

要用courier send 去代理

---

作者: tomleehk    時間: 2014-11-22 00:52

Good luck..

---

作者: 病態賭徒    時間: 2014-11-26 10:17

已經換了一個新回來, 希望唔好又整死

---

作者: tomleehk    時間: 2014-11-26 11:51

本帖最後由 tomleehk 於 2014-11-26 11:53 編輯

It seems there are only 4 possible files for E1200 v2
http://www.4shared.com/dir/v1BuI ... s.html#dir=yIMXihqB
[attach]1739084[/attach]
http://www.4shared.com/dir/v1BuI ... s.html#dir=sz5zA-5p
[attach]1739085[/attach]

I really have no way to tell if any one of these able to provide JFFS feature.

---

作者: 病態賭徒    時間: 2014-11-26 12:07

I will try one by one, thx again

---

作者: 病態賭徒    時間: 2014-12-2 19:55

Flash 了一個，仲有3MB可以用，但唔知做乜winscp入唔到。

---

作者: tomleehk    時間: 2014-12-3 01:08

本帖最後由 tomleehk 於 2014-12-3 09:04 編輯


A little bit tricky..

Via Tomato GUI, you need to enable the SSH first.

Then connect via winscp
Protocol:SCP
Login ID : root                             
Password : <password of admin>

http://www.myopenrouter.com/arti ... o-Firmware-via-SSH/

---

作者: 病態賭徒    時間: 2014-12-3 11:05


明白大大,

你上次話只是需要兩個files...
想confirm which 2

Thxxxx

---

作者: tomleehk    時間: 2014-12-3 12:41

本帖最後由 tomleehk 於 2014-12-3 12:46 編輯



hamcore.se2
vpmserver

---

作者: 病態賭徒    時間: 2014-12-3 22:43

多謝大大, 行前了幾步

以下screen唔知入乜

---

作者: tomleehk    時間: 2014-12-3 23:10

本帖最後由 tomleehk 於 2014-12-3 23:12 編輯

This is for your VPN virtual network configuration..
Must use a different subnet from what you configure for the LAN segement in Tomato..

---

作者: 病態賭徒    時間: 2014-12-4 00:10




    in Tomato (AP mode as I have a core Router), the IP is set to 192.168.11.100
the virtual hub IP setting will be 192.168.xxx.1 where xxx cannot be 11, the rest (except subnet C) just follow the picture above?

---

作者: tomleehk    時間: 2014-12-4 00:22

OK....